Monday, September 22, 2014

Lab 8 C21 Electricity ->Balloon, Tape Interactions, Electrical static Force Law, Vander Graff applications of hair, franklin generator ,ribbon, plasma ball, and how Van Der Graff works.<-

Balloon

The setup of the pictures above shows that Prof Mason used the fur to rub the balloon and once the fur has been
From the two pic above, Prof Mason is trying to let the balloon stick to the wall. It failed first time because it has not been rubbed enough.


1. ball with fur and fur attract

Rubbed rubber with silk and fur, which both effected ballon sticking to the glass. 

Demonstration of balloon sticking to glass with diagrams

Charge compared to mass and they are very similar F=ma  Ef=qE


Charge defined for 7 year old.
Tape Interactions
Demonstration of positive and negatively charged tape.
had to cooperate other groups for video due to technical difficulties


 The two videos shows how opposite charged tape attract and same charged tape repel.

Electrical static Force Law
2 frame persecond representation of electrostatic forces visually
The video above will be used for experimental data for calculation based on E=KQ/r^2 equation. 




Angle expression with Dx and L.

Steps for electrical static forces calculations


Computer generated value for r, A, and eqquation for the force over distance r.

Because other E=KQ/r^2 only r is the variable and others are constant thus we have this shape.



More steps shown here for force over distance r^2 derive from pixel count of the video experiment.


Vander Graff applications of hair, franklin generator ,ribbon, plasma ball, and how Van Der Graff works.

Hair

Franklin generator

Flying ribbon(did not)
This one fails because of the weight of ribbon is comparatively heavy and it has a relative thin plastic coating on it.

Plasma Glass balls 
Inside, there is a low pressurized gas that makes electrical charge shoot at low voltage.
Voltage is defined by the electrical pressure. The higher the pressure increases the distance it can push a spark. Furthermore, the sparks are at high frequency due to low pressure gas inside.

Below are two pic below for showing how Van Der Graff generator works. Rubbing electrons by a motor with a belt full of electrons and metal conducts the electrons outward through ground that generates a flow of electron.

Wednesday, September 17, 2014

Lab 7 ->Green Liquid and entropy, Setup and some analysis of Sterling Engine, Floors/Minute calculations<-

Green Liquid and entropy
Green Juice liquid into white water in beaker.
The greenish liquid diffuses into clear liquid when it is poured into the beaker to show that the mysterious liquid is now inside both containers and total system has more entropy.

The magical green juice is increasing the entropy of both the bottle and beaker system.








Setup and some analysis of Sterling Engine
Introduction of stirling engine. In class, Professor Mason described a detailed analysis of his thought that Sterling engine versus the solar power cells.

Stirling engine bird eye perspective

Ice on top of stirling engine.


Heating up the stirling engine with oven.
   In this part of the lab, a sterling engine was studied to see how the difference in temperature is used to operate it. Due to the displacement piston being made of foam, it resulted in a very small amount of pressure due to pressure leak. 
   First, a hot water reservoir was on the bottom, a beaker of water on a hot plate, and then a cold reservoir was placed on top with ice cubes. All sterling engines have very low energy cycles and have very low power. A great example is how they are used is with solar energy. The sun provides the hotter temperature side, and the earth underground provides the cooler side and that difference in temperature gets the sterling engine working. Despite the sterling engine working pretty simply, the only issue is that energy is not being generated directly, instead it is mechanical work that needs to be converted into electricity.

Calculation of Efficiency of Stirling engine
Floors/Minute calculations
Human can use 760 Watts or 1 hp of power for a short period.
M 100kg and floor height about 5 meters. And the calculation shows 9.3 floors per minute to use 1 hp of power. However, a man can not sustain that for a long distance or long time.
Calculation of 1 hp of power.





Sunday, September 14, 2014

Quiz 2

Diesel Cycle
Adiadatic

This was the process that we go from the study session, which got some variables wrong.
The most important lesson learned was that in adiabatic process the energy does not always stay constant.


Friday, September 12, 2014

Lab 6 , PV diagram, carnot cycle, ->Hypnotize Heat Engine(Thermoelectric motor), The Pressure Lifter with PV diagram, Typical Heat Engine<-



Hypnotize Heat Engine(Thermoelectric motor)
The left side got colder by approximately 18 Celsius as shown in the picture because it is gathering white surface on the left metal plate. Also, there is a gyroscopic force acting from the spinning force on the whole system of the thermoelectric motor that moves on the table. Furthermore, since the picture is taken.
Teacher used the approximately the about the same amount of water from measuring from beaker to the water heater(first process not shown). Two cups were made of heat insulating material to prevent unnecessary heat transfer to the environment. At, first the boiling water didn't work even after waiting for at least 30 seconds for the motor to start spinning.
Setup for the very beginning of experiment.
Here is the thermoelectric motor that teacher hooked up a thermoelectric generator with a approximately 3V DC toy brushed motor. Along with the card-box on the bottom as the structure for the whole system to stay in place.
Setup for the first part: Cold ice water vs. warm water.

 Setup for Second experiment. Ice water in one and flaming torch ready to heat up other side.
In this picture, the thermoelectric motor is stabilized in the icy water cup and the other side is ready to be heat up.



The Flame torch vs ice water. The heat on the propane flame torch side can reach up to two thousand degree Celsius, and thus we can have a max deltaT in the most ideal situation of Th-Tc=2000-0=2000C for the thermoelectric motor to spin up the hypnotizing disk.

After approximately 5 seconds of waiting, the wheel start to spin, which is shown in the next picture step.

The wheels starts to spin in the counter-clock fashion and keeps on spinning at counter-clock fashion even after the flame torch is moved away. 
 Set up for #3 of the first experiment. We first cooled the hot plate first in warm water.
The hypnotizing's speed did not really change noticeably even when we tried to cool it down in the warm water.
 Then, we cooled it in the ice water.

When we changed the hot side to the cold side, we almost immediately see a slow down of the hypnotizing disk.

After the hypnotizing disk's speed slowed down, we put the the two plates of thermoelectric motor in opposite ways. 

The hypnotizing disk is spinning now in a clockwise fashion. with the now boiling water on the left cup and cold water one the right cup.
 Setup for #4 of first experimental demonstration. This part is similar in  effect similar to that of refrigerator using energy to cool the a system.
After the hooking up the wires to the toy dc motor. We hooked up right to red power wire and left to ground wire with a power of .33 volt and 1.00 amperes. 


The spinning force of the hypnotizing disk gives the gyroscopic force to make the whole system of the thermoelectric move to the right from the picture above. 
 From the setup of the second experiment, we found out
The Pressure Lifter with PV diagram
The first syringe has a leak in the system in the tubing part.


Drawing of setup.





All three pics show the complete overview of setup that has the syringe changed and fixed loss of pressure problem.

Teacher's Automated computer calculation of the integral.

Vector calculation used: vector AB and AC cross product and times by 2 =24.5cc*kpa which was similar to teacher's answer.
 Setup for question finding the area inside the parallelogram using cross product from math 280 of treating AB, AC, DC, DB as vectors and finding their magnitude divided by 2.

 Set up for Carnot cycle, replace pic for max carnot is 33percent realistically.




 Demonstration of the four stroke cycle using half cross-sectioned model
There are four stages in the engine cycle with a spark plug.
First stage is intake.

Here is the general setup of a intake part of the cycle which takes both air and gas into the piston chamber. 
 Second stage: compression of
The finger points to the first stage of the four-stroke setup as the cylinder inside expand and thus more moles and volume will be in the chamber. Then, for second 
 Third step: combustion(sparkplug)
In this picture, the sparkplug is then igniting the compressed mixture of air and fuel from the previous stage where air and sucked into the system.
 Fourth step, exhaust out.

3 variables to know for power of heat engine.
W, Qh, Qc: Work done overall, and heat reservoir into heat engine, cold resevoir out from heat engine(cooler, environment)